Panasonic PT-REQ80 雷射工程投影機(請來電詢問)
-鏡頭位移功能(視鏡頭)
-支援360度安裝
商品介紹
規格說明
※本網站所提供產品規格內容如有變更，恕不另行通知。實際請以各廠牌官方最新公告資訊為主。
|
Projector type |
1-Chip DLP™ projectors |
|
Light Source |
Laser diode |
|
DLP™ Chip | Panel Size |
0.8 in diagonal (16:10 aspect ratio) |
|
DLP™ chip | Number of Pixels |
2,304,000 (1920 x 1200 pixels) |
|
Light Output*1 *2 |
8,000 lm / 8,200 lm (Center)*3 |
|
Screen Size (Diagonal) |
70–700 inches (with supplied lens) |
|
Resolution |
4K (3840 x 2400 pixels) (Quad Pixel Drive: ON) |
|
Contrast Ratio*1 |
25,000:1 (Full On/Full O , Dynamic Contrast [3]) |
|
Time until light output declines to 50%*4 |
20,000 hours (NORMAL/QUIET), 24,000 hours (ECO) |
|
Center-to-corner zone ratio*1 |
90 % |
|
Lens |
PT-REQ12/REQ10/REQ80: Powered zoom (throw ratio 1.36–2.10:1 for supplied lens),powered focus;PT-REQ12L/REQ10L/REQ80L: Optional powered zoom/focus lenses |
|
Lens shift | Vertical(From the originpoint of the lens mounter) |
±60 % (with ET-C1W400/W500/S600/T700), ±50 % (with ET-C1W300/U100) |
|
Lens shift | Horizontal(From the originpoint of the lens mounter) |
±29 % (with ET-C1W400/W500/S600/T700), ±23 % (with ET-C1W300/U100) |
|
Keystone Correction Range |
Vertical: ±40 ° (±5 ° with ET-C1U100; ±10 ° with ET-C1W300; ±16 ° with ET-C1W400; ±22 °with ET-C1W500),Horizontal: ±40 ° (±3 ° with ET-C1U100; ±5 ° with ET-C1W300; ±10 ° withET-C1W400; ±15 ° with ET-C1W500) |
|
Terminals | HDMI™ 1/2 IN |
HDMI™ x 2 (Deep Color, compatible with HDCP 2.3, 4K/60p signal input) |
|
Terminals | DisplayPort™ |
DisplayPort™ x 1 (Deep Color, compatible with HDCP 2.3, 4K/60p signal input) |
|
Terminals | Multi Sync In |
BNC x 1 |
|
Terminals | Multi Sync Out |
BNC x 1 |
|
Terminals | Serial In |
D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
|
Terminals | Serial Out |
D-sub 9-pin (male) x 1 for link control (RS-232C compliant) |
|
Terminals | REMOTE 1 IN |
M3 stereo mini-jack x 1 for wired remote control |
|
Terminals | REMOTE 1 OUT |
M3 stereo mini-jack x 1 for link control (for wired remote control) |
|
Terminals | Remote 2 In |
D-sub 9-pin (female) x 1 for external control (parallel) |
|
Terminals | LAN |
RJ-45 x 1 for network connection, PJLink™ (Class 2) compatible, 10Base-T/100Base-TX, Art-Net compatible |
|
Terminals | USB |
USB connector (Type A) x 1 for optional AJ-WM50 Series Wireless Module/USB memory |
|
Terminals | DC Out |
USB Type A x 1 (for power supply, DC 5 V, 2 A) |
|
Terminals | Expansion Slot |
Open slot for for function boards, Intel® SDM compatible |
|
Protocol versions |
IPv4, IPv6*5 |
|
Power Supply |
AC 100–240 V, 50/60 Hz |
|
Power consumption*6 | Maximumpower consumption |
760 W (7.7–3.2 A) (770 VA) (Power consumption is 730 W at AC 200–240 V) |
|
Power Consumption*6 | On-modepower consumption (Operatingmode) Nomal |
595 W (AC 100–120 V), 575 W (AC 200–240 V) |
|
Power Consumption*6 | On-modepower consumption (Operatingmode) ECO |
470 W (AC 100–120 V), 455 W (AC 200–240 V) |
|
Power Consumption*6 | On-modepower consumption (Operatingmode) QUIET |
465 W (AC 100–120 V), 450 W (AC 200–240 V) |
|
Operation noise*1 |
35 dB (NORMAL/ECO), 32 dB (QUIET) |
|
Dimensions (W x H x D) |
PT-REQ12/REQ10/REQ80: 498 x 212 x 648 mm (25 1/2˝ x 8 11/32˝ x 21 3/16˝) (With feetat shortest position)PT-REQ12L/REQ10L/REQ80L: 498 x 212 x 538 mm (19 5/8˝ x 8 11/32˝x 21 3/16˝ ) (With feet at shortest position) |
|
Weight*7 |
PT-REQ12/REQ10/REQ80: Approx. 28.7 kg (63.28 lbs) (with supplied lens), PT-REQ12L/REQ10L/REQ80L: Approx. 27.0 kg (59.53 lbs) (without lens) |
|
Operating Environment |
Operating temperature: 0–45 °C (32–113 °F)*8, operating humidity: 10–80 % (nocondensation) |
|
Applicable Software |
Logo Transfer Software, Multi Monitoring & Control Software, Projector Network SetupSoftware, Real-Time Tracking Projection-Mapping System,Early Warning Software,Geometry Manager Pro, Smart Projector Control for iOS/Android™ |
|
Control function via LAN |
Crestron Connected™ V2, Crestron XiO Cloud™, Art-Net DMX, AMX® DD, and PJLink™(Class 2) |
|
Note |
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC21118: 2020 international standards. Value is the average of all products when shipped.*2 When [OPERATING MODE] is set to [NORMAL]. *3 Average light output value of allshipped products measured at center of screen in [NORMAL] Mode. *4 Around this time,light output will have decreased by approximately 50 %. IEC62087: 2008 BroadcastContents, Dynamic Contrast [3], temperature 30 °C (86 °F), elevation 700 m (2,297 ft) with0.15 mg/m3 of airborne particulate matter. Estimated time until light output declines to 50% varies depending on the environment. *5 Optional AJ-WM50 Series Wireless Module isnot compatible with IPv6. *6 Measurement, measuring conditions, and method ofnotation all comply with ISO/IEC 21118: 2020 international standards. On-mode powerconsumption measured at 25 °C (77 °F) operating temperature at an altitude of 700 m(2,297 ft). *7 Average value. May diff er depending on the actual unit. *8 When theoptional AJ-WM50 Series wireless module is attached, the operating temperature rangebecomes 0–40 °C (32–104 °F). The operating environment temperature should bebetween 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between1,400 m (4,593 ft) and 4,200 m (13,780 ft). |
運送方式
運送說明
1.本網站訂購之商品將於訂單轉出後統一由服務人員與您聯繫配送，本公司配合物流如下：
*神行貨運。
*台快貨運。
*宅急便物流。
*便利帶物流。
*郵局。
*宏程自行配送。
**商品如無特殊情況( 遇原廠缺貨、客戶延期.....等)將於2個工作日內出貨。配送時間依照各地物流配達為主。如需詢問可透過官方LINE：@daka1788 或電話 02-23942890 詢問配送進度。
2.詳細配送說明
(1)商品如標示免運費。則消費者毋須負擔運費。
(2)如遇偏遠地區，將依地區收取偏遠運費。
(3)不提供舊機拆卸安裝與回收服務
(4)詳細配送條件將於訂單確認時由專員與您核對。
(6)如遇無電梯之樓層，將依樓層收取樓層費。
(7)貨運僅配送額外服務需求將依現場報價收取。
3.影音產品配送
(1)商品將於訂單付款完成後2個工作天內出貨。
(2)商品將依據大小、地區，調整配送方式，恕不可指定配送商
提醒您。於宏程購物網購買之商品必須於網頁申請退換貨：點我前往(電話或口頭告知皆不成立)
依照消費者保護法規定，消費者均享有產品到貨7天猶豫期之權益(注意！猶豫期非試用期)，但提醒您，商品退貨時必須是全新狀態且包裝完整，所有內容物必須回復原狀，亦即必須回復至您收到商品時的原始狀態 (包含主機、附件、內外包裝、隨機文件、贈品等)，若為部分商品退貨則針對您已使用或保留之商品應另以市價計價，否則將影響您退貨的權限。
*7天猶豫期（非試用期）內進行商品退換貨時，應負有回復原狀之義務。
*退換貨商品必須是全新商品，商品與盒裝外觀不得有刮傷、破損、受潮、塗寫文字，且必須保有相關配件（保護袋、配件包裝、保麗龍、贈品、所附文件...等）之完整性。
*猶豫期內請保留原「運送外箱」，勿讓物流商或貨運公司收走，以便退換貨返還時保護商品使用。
*另投影機，顯示器、音響除產品本身故障或瑕疵外，一經使用將會影響退貨權限。
<<特殊情況無法退貨>>
1. 商品因消費者個人因素需延後配送超過訂單日7天以上。經告知為保留商品無法退貨後，即不允退貨。
2. 商品原始外包裝與包材(紙箱、保麗龍、保護材….等)遺失、損毀或非使用原始包材，因無法確保物流配送狀況，則不允退貨。
3. 經原廠判定為人為損壞商品，因商品已無法復原原始狀態，不允退貨。
<<換貨流程>>
1. 商品經使用者開封使用後，如商品本身瑕疵，將通知原廠服務站到府檢測。
2. 原廠確認新品不良後，始可換貨。
3. 非商品本身瑕疵換貨，消費者如無法復原原始商品，須負擔整新費用(依照使用程度逐項收取)。
4. 非新品猶豫期間內提出申請換貨(商品送達後7日後)，將由原廠服務站與消費者說明後續處理。
<<特別說明>>
1. 大型商品退貨原因如為商品異常，將請原廠指定服務單位到府鑑定商品，請於退貨時一併將檢測單據附上，如無法附上或拒絕原廠指定服務單位到府檢測將視為良品退貨，並依照使用程度逐項收取費用。
2. 大型商品回收時將於回收地點現場基本商品狀況確認，如消費者拒絕人員確認或無法於取回地點確認，經人員回報後，則不允回收商品並拒絕退貨。
3. 配送或回收商品僅有一次免費派遣，如因消費者因素造成二派情況，產生費用將由消費者支付。
4. 配送人員安裝商品，視同消費者使用商品，如對商品有疑慮，消費者有權選擇不安裝
5. 本公司收到您下單(要約)後，仍需確認交易條件正確、供貨商品有庫存或服務可提供。如有無法接受訂單之異常情形，或您下單後未能完成正常付款，應視為訂單(買賣契約)全部自始不成立或失效，本公司得於合理期間內通知說明拒絕接受訂單。請您重新依需求下單訂購。
